With these conditions met, the cam-idle will activate and remain active until the next key-cycle, when all the conditions are checked again. There must not be any detected failures of the engine control related sensors or actuators.(Note that it is sufficient just to rev it up in neutral or drive away once the other conditions have been met and cam-idle mode will be enabled) The engine must not currently be idling.130 seconds have elapsed since the engine coolant temperature reached 170 ☏ (77 ☌) while the engine is running. BAMA Performance does not offer any revisions or datalogging to accommodate calibration symptoms of this nature produced by the Ghost Cam tunes. **Please Note - This is a novelty tune and can produce some stalling, surging, or drive-ability issues. With the tune loaded onto the Mustang, three conditions must be met for the Ghost Cam idle to enable: Ghost Cam tunes utilize the Mustang's Twin Independent Variable Cam Timing (TiVCT) to make the engine sound and feel race-ready. If your 2015-2017 V6 Mustang does not produce the signature Ghost Cam sound after uploading the tune, this is a result of the strategy code. Some strategies do not have all of the information to produce the Ghost Cam effect. When you order a tuner, you arent just getting a tuner - you are getting the tuner and 2 dyno-tested custom Bama tunes:Performance (87-93 octane) - The Performance program is designed to add power at 3000 RPMs and higher, focusing more on the top end horsepower and all out performance driving. Some 2015-2017 V6 Mustangs are capable of producing the Ghost Cam effect, however, this is dependent on the strategy code. Ghost Cam calibrations are available for both Off-Road and Catt'ed exhaust systems. I like the customization features and the shift light function. Personally Im looking into a Ngauge with PBD tune when I install the ported GT-350 IM and 47 lbers. Once the data log is saved it is ready to be emailed to our technicians for review.BAMA Performance offers a Ghost Cam 2011-2015 Mustang GT and 2011-2014 V6 Mustangs equipped with both automatic and manual transmission. I have a friend thats Bama tuned w/tuner and wishes he went another route. Label the log file with the name of the test you performed.ġ1. Click on the arrow to the right of Save and select "Save All". Save the data log by clicking the Save button in the tool bar (under the data log tab) at the top of Livelink. To see a list of the tests and how to perform them click here - What data logging tests do I need to perform?ġ0. Complete whatever test it is you need to do and when you are ready to stop the log, click on the device in the top left corner with the red dot. Once you click on it start your vehicle and you will see data moving across the graph. When you are ready to start data logging, start your vehicle and click on the picture of the device in the top left corner with the green dot next to it. In the tool bar at the top select “Save Config”. Next you will want to save your configuration file so you will not have to select the parameters again in the future. You will then see all of the parameters you selected appear along with some gauges.Ĩ. Once you have selected all of the parameters click “Configure Datalog” at the bottom right corner. Choosing an OBD parameter will result in poor data logging results. Note: It is very important to only choose PID and DMR parameters while datalogging. You can find what parameters you will need on this list here What Parameters Do I Need To Data Log? Select the parameters that are needed for your vehicle. On the vehicle information screen select "Validate All Items" and then select "select items".ħ. Click the Vehicle Info button in the bottom right corner.Ħ. Once the question marks turn into numbers you know that you have good communication with the vehicle. The other great thing about the handheld bama tuner is that you. The 87 tune isn’t as good but it’s still quite noticeable when you put your foot down. You’ll definitely feel a boost in torque especially if you already have some mods. Next with the tuner plugged into the vehicle and the laptop press "Check Communication" on the Communications screen. I’ve been running my 4.0 at the 93 octane tune for over a year now and I love it. Next turn your key to the on position but do not start the vehicle until you are ready to record the log.ĥ. Follow the prompts to plug in the device to the vehicle and laptop.Ĥ. From the home screen of LiveLink select "I want to datalog a vehicle".ģ. Download and install LiveLink Gen-II data logging software here.Ģ. Click here for instructions on how to determine if your device is up to date and to download the SCT Device Updater Software, which is required to complete this process.ġ. Make sure you are running the most recent version of the software and device firmware. If you have been requested by Bama Performance to perform a datalog with Bama, follow these instructions.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |